Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
The publisher is making a few great pointers on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this content further down.
Mounting a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a new one is also a reasonably hard project. If the old bathtub is easily accessible, the project can move quickly; if you have to open a wall surface to eliminate the old bathtub and place the new bath tub, the job is a lot harder. In either situation, the task is within a residence handyman's skills, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have qualified yourself for the work as well as are comfortable attempting it. Instead of employing a service provider to take over a halfway-completed task, it is much better to think about utilizing one before you start. Opportunities are you may require a professional plumber to make tube connections.
This short article will help you set up a brand-new bathtub in your restroom if you have already purchased a new bathtub as well as don't require to alter the plan of your previous water supply pipes.
Your tools and material list should consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be fairly troublesome due to the limited access that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric ready for the staying water that will come from the pipes. When the supply pipelines have actually been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making sure that the washing machines are in location in between the tap and the sink. Secure the faucet in place with the manufacturer offered backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The former kind ought to be connected to the tap ends initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Making use of the two wood boards under its feet, position the bathtub in the called for placement. The wood boards are practical in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level and adjusting the feet on the bath tub till the level reads degree.
To set up taps, fit all-time low of the furthest adaptable faucet port to the proper supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the water system and inspect all joints and also new pipework for leaks and also tighten them if necessary. Load the bathtub as well as additionally examine the overflow electrical outlet and the normal outlet for leaks.
Ultimately, deal with the bath paneling as defined in the producer's instruction manual. Tiling and also securing around the bathtub should wait till the bath tub has actually been used at least when as this will resolve it right into its final placement.
Planning for the Setup
Firstly, the sustaining frame provided with the bath should be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the versatile tap adapters to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before sealing, to enable the activity experienced when the tub remains in usage. The sealant can fracture relatively early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece of writing about How to Install a Bathtub Yourself while doing a search on the search engines. Do you know somebody else who is very much interested in Installing A Bathtub? Do not hesitate to share it. Kudos for your time. Please check our website back soon.
Choose our certified emergency plumbers. Report this page